View Full Version : cable autobouquets (not ABM)
hi all
installed cable autobouquets in extensions folder and dvbsnoop in bin folder set permissions to 755 on both files i go in plugin and get error message "autobouquets c2 module has no attributres plugin."
any help on what is wrong please normal sat autobouqet maker works perfect.
Thanks
Eggie
abu baniaz
22-03-15, 19:28
Doesn't ABM work for you?
If you are going to use AB Cable, better to install by using the ipk.
Hi
ABM get error message module timeout but e2 ABM works but on sat side but not cable side.
tried the ipk method but still same error module no attribute
plug in.
Any other way to get cable ABM working please.
Thanks
eggie
abu baniaz
22-03-15, 21:07
If you are sure that you are using correct Net ID for ABM, the main reason it will fail will be signal related.
For AB cable, just make teh whole folder 755. Double check you have installed dvbsnoop
hi
i have correct net id has cable channels ok , when i install the plugin and set file permission to 755 on dvbsnoop and cable abm . When i go into plugins i get the error message cable autobouquets module no attributes. I dont see the plugin in my plugin folder on vix appollo 156. I can get the e2 plugin to work on sat side but wont scan cable thats why i trying to install cable abm but wont show in plugin folder. I have tried the ipk method but still wont show . I keep getting error message when i go into plugin folder as above.
any help appreciated.
thanks
Eggie
abu baniaz
22-03-15, 21:22
Delete teh cable plugin from your previous attempt. Install the ipk by telnet. Post back the results of your telnet console.
Hi
Got tjhe plugin installed and showing in plugin folder now the problem when i start the plugin i get file permission denied . I have set the permissions to 755 , the plugin i am seeing is cable e2 front end and when i start i get file permission denied.
Any help appreciated.
Thanks
Eggie
Hi all
Used tenet commands
cd /tmp/
./autobouquets_c2.sh
get permission denied i did login amd get the first login line as
root@quadplus: /var/volatile/tmp# ./autobouquets_c2.sh
-sh: ./autobouquets_c2.sh: permission denied
any help appreciated.
Thanks
Eggie
abu baniaz
22-03-15, 23:07
Please remove the version you have installed.
Install this version
http://www.world-of-satellite.com/showthread.php?35089-Lraizer-Autobouquets-E2-UK-Cable&p=326831&viewfull=1#post326831
You will be able to run from GUI
hi abu
I cant see the commands even though i am a member this is what i,m seeing
Please try this one.
It is Lriazer's work, any credit goes to him.
We have done the following:
Added a check for dvbsnoop
Modified the bouquet names
Removed the channel number
Transfer to /tmp/ and install by using following command
Code:
Please register to view content. Only take's a few seconds!
You will need to install dvbsnoop using command
Code:
Please register to view content. Only take's a few seconds!
Plugin must be run while on an active channel.
Pure areas are not listed. Select "Any Pure Area"
Attached Files Attached Files
File Type: ipk enigma2-plugin-extensions-autobouquets-c2lite_2014_11_20_all.ipk (12.4 KB, 94 views)
please can you tell me what commands i need please.
Thanks
Eggie
abu baniaz
23-03-15, 22:31
I can't see the comments even though I wrote them! :confused:
Just corrected it. :)
hi abu
thanks for that
eggie
hi
Do i need to set net id for leave it blank
Thanks
Eggie
Hi abu
Thanks for the help its working fine i justbset net id from gui.
Eggie
abu baniaz
23-03-15, 23:16
Just use the GUI for now. You must be on a working channel prior to running the plugin. BBC2 is a good one to use. Or even the EPG channel even though it is blank. There is an example setup on post 1 of that thread.
Please note, I wil be moving this thread to the plugin support section later
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.