View Full Version : DM800HD New Hardware Drivers
01-05-2011
- hotfix freeze after some channel changes
- throttled mpeg decoder debug output a bit
- fixed bcm4506 tuner crash (no hab ack messages in kernel debug)
- fixed bcm4506 manual LDPC FEC modes
- fixed readback of current pilot state for dvb-s2 frontends (needs a linuxtv api fix)
- readback corrected symbolrate and frequency for bcm4501 and bcm4506
- cxd1981 DVB-C optimizations
update dm500hd,dm800se,dm8000,dm7025,dm800 hardware drivers
- bcm4506: reintroduce minimum tune timeout of 1,5sek to fix tune failed problems caused by slow SEC switches
WARNING
these drivers are for original dreambox receivers only, do not attempt to flash to a cloned unit as it may cause damage.
http://sources.dreamboxupdate.com/opendreambox/1.6/dm800/feed-rel_31/dm800/dreambox-dvb-modules_2.6.18-7.4-dm800-20110504-r0_dm800.ipk
bcm4506/bcm4501 fixed broken toneburst handling (broken since 20110501 drivers)
WARNING
these drivers are for original dreambox receivers only, do not attempt to flash to a cloned unit as it may cause damage.
http://sources.dreamboxupdate.com/opendreambox/1.6/dm800/feed-rel_31/dm800/dreambox-dvb-modules_2.6.18-7.4-dm800-20110506-r0_dm800.ipk
DM800HD New Hardware Drivers 09-11-2011
dreambox-dvb-modules.bb: update dreambox hardware drivers
dm800/dm8000:
- fixed sometimes inoperable hdmi audio after code change to AAC/MP3
dm7020hd:
- fixed bcm4505 tuner detection problems on boot from deep standby
- fixed support for high bitrate transponders (no CI support yet)
all:
- dont allow to allocate a demux pid filter for fake pid 0x2000
- fixed inoperable AUDIO button on DM7020HD remote control (dip switch depending)
- optimized blindscan (ignore duplicate found TPs, low SR crash)
DM800HD New Hardware Drivers 09-11-2011
dreambox-dvb-modules.bb: update dreambox hardware drivers
dm800/dm8000:
- fixed sometimes inoperable hdmi audio after code change to AAC/MP3
dm7020hd:
- fixed bcm4505 tuner detection problems on boot from deep standby
- fixed support for high bitrate transponders (no CI support yet)
all:
- dont allow to allocate a demux pid filter for fake pid 0x2000
- fixed inoperable AUDIO button on DM7020HD remote control (dip switch depending)
- optimized blindscan (ignore duplicate found TPs, low SR crash)
Hi, can I put this in my DB 800 HD PVR sim 2.0.1 probably clon resiver. Thanks
No these drivers are for original dreambox receivers only. Also.please be aware that we don't provide any support on this forum for cloned receivers.
Sent from my HTC Desire using Tapatalk
02-02-2012
update dreambox hardware drivers
- cxd1981(hybrid DVB-C/-T) increased max. frequency to 900Mhz
- cxd1981(hybrid DVB-T) fixed ineffective 5V for active antennas after mode change
- bcm4505/6 improved receiption sensitivity (fixes problems with small dishes since blindscan support)
dm500hd,dm800se,dm7020hd: fixed audio volume boost on alsa playback
dm7020hd:
- fixed frequently "error code 0x18006" messages on bootup
10-02-2012
update dm800 hardware drivers
- fixed strange aliasing noise on PCM Playback with needed upsampling
- finally fixed hybrid DVB-C/-T Tuner 5V output for active antennas
- don't fallback to DVI when the HDMI EDID was not readable
(this fixes some HDMI audio/video problems)
updated hardware drivers 16.02.2012
update dm500hd, dm800se, dm8000, dm7020hd and dm800 hardware drivers
- fixed overflow on aspect ratio calculation
this fixes possible wrong scaled content
- fixed scale factor calculation for dm800
i.e. fixes wrong scaled IPTV services
- fixed non transparent framebuffer after bootup
this fixes not visible bootlogo before e2 starts on dm800
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.