Hi
Blaze does not clear on either my ZGemma or my GigaBlue receivers, is this a LNB or alignment issue?
Blaze.jpg
Hi
Blaze does not clear on either my ZGemma or my GigaBlue receivers, is this a LNB or alignment issue?
Blaze.jpg
transponder change :
28.2°E 1Astra 2G 11082.25 H 65 Europe DVB-S2 8PSK 23000 2/3 ASTRA, 44.5 Mb/s 2 2065 KingOfSat charts update form
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
I tried a AutoBouquetMaker update and scan , and it has not changed
its gone from dvb -s to dvb -s2 and the s/r changed from 22000 to 23000 just use signal finder with the above and you will get it.
What am i doing wrong?
scan.jpg
we only see half and you have no reception on that transponder 0-0%
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
a bit of a mysteru, can you put in a known frequency to show tuner is ok. to save you thinking its not there here is my pic on uno4kse
ABM brings this fine for me.
If you perform a manual scan (single satellite), how many channels do you get?
maybe first update satelites XML
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
abu baniaz (29-07-24)
Thanks, very good point. Using the xml update plugin which is pre-installed in ViX will obtain latest file. It is within the tuners and scanning page. It is used by enigma2 scanning, signal finder. It is NOT used by ABM to obtain services.
Blaze is on 11082 MHz, Horizontal, 23000 2/3
Sorry for the delay coming back was busy yesterday.
Have done a manual scan and got 620 channels.
Updated the xml rebooted and tried Blaze again
update.jpg
Details seem the same as Abu's but no lock
maybe try to adjust the LNB because blase enters here with 100% 14.9 db
VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
Triax 88 cm rotor single LNB 30 E- 40 W
1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E
You should be getting about 800. You are missing about a quarter, I think your LNB has become faulty. If you remove all the channels, don't use ABM, perform a manual scan again, you can better guage what you are missing. If one of the four planes/quadrant, it will definitely be an LNB fault. (Pity diseqc tester does not work as well as it could do.)
Got round to replacing LNB, and everything now working properly.
Thanks to everyone for the help
abu baniaz (21-09-24)