AB-Com PULSe 4K SE only £99! FREE UK DELIVERY!
Superb quality and spec AB-Com PULSe 4K SE only £99! FREE UK DELIVERY! 4K UHD, Enigma 2, Multiboot 4 images & more!...
AB-Com PULSe 4k Rev II Twin tuner only £149! FREE UK DELIVERY!
Superb quality and spec AB-Com PULSe 4K Rev II Twin Satellite tuner only £149! FREE UK DELIVERY! 4K UHD, Enigma 2, SATA HDD facility, Multiboot 4 images & more!...

Dual tuner streaming

S

sebus

New member
Joined
Jan 26, 2013
Messages
65
Reaction score
0
Points
0
Location
Island on the edge of Europe
Multi LNB on a motor. One cable goes to TunerA, second to TunerB

TunerA = positioner
TunerB = second cable...

Can stream any single channel with no issue.

But if I watch a channel on TV, on few channels streaming a different channel (different transponder) is almost impossible (it breaks all the time). While the one on TV is fine or the other way round)

But some combinations of 2 different channels is fine for simultaneous watching & streaming.

So I do not think it is that H7 is not powerful enough to do that
I think I have some settings incorrect.

Is there a way for "force" channel to be received via specific Tuner?

Thanks

sebus
 
Last edited:
It should work fine as long as tuner A doesn't aim the dish away from what Tuner B is receiving.
 
What levels are showing on signal on both tuners.
 
When the dish here was out of alignment and some signals were okay while others were weak or unusable I did find that when one tuner changing transponder could change the S/N ratio on the other enough to change it from weak but usable to not working at all.
But if you have signals that bad something is wrong with the dish alignment, the LNB or the wiring.

Can you tell us some of the combinations that work and don't work?
 
sebus said:
Should being the operative word. Some do, some do not. It is a single LNB with 2 cables out, so no way to aim it at something different!
Click to expand...

Then what did you mean by positioner and motor here:
sebus said:
Multi LNB on a motor. One cable goes to TunerA, second to TunerB

TunerA = positioner
TunerB = second cable...
Click to expand...
 
Have tested & redone both cables
Each cable separate works fine

But from quad LNB I can only stream a channel & watch another channel from the same TP (like describe here)

It makes no difference if channels are enc or FTA

sebus
 
Last edited:
It is all in first post

There is no recording involved

One channel on TV & another one streamed to PC

Two DO work ONLY if both coming from same transponder
 
Ok, so you don't want to provide the channel names. Also need settings file from /etc/enigma2.
 
It does not matter what channels they are, it is the same for each & any pair (same transponder = both fine, different transponders = only first one "wins")
Also it makes no difference in behaviour if they are FTA or encrypted channels

View attachment settings.txt
 
Last edited:
If you are using pure2 which is what your signature says, then I would suggest you flash openvix and try that…..I have no idea what pure2 are based on as they block access to their code ( they are obviously superior to everybody else), but I assume its openatv which uses different code for tuners.
 
sebus said:
It does not matter what channels they are, it is the same for each & any pair (same transponder = both fine, different transponders = only first one "wins")
Also it makes no difference in behaviour if they are FTA or encrypted channels
Click to expand...
So it behaves like only one Tuner is working.
Check both tuners are correctly connected and correctly configured.
 
If you don't have openvix loaded you are posting on the wrong forum.
 
You must log in or register to reply here.

OpenViX Feeds Status

Back
Top