[VU+ Solo2] CrossEPG scheduled download not working

[abu baniaz]

both are simple, single, 28.2

Did you use the automatically select function when setting the tuner?

This is yours

config.Nims.1.diseqcA=282
config.Nims.1.diseqcB=3601
config.Nims.1.diseqcC=3601
config.Nims.1.diseqcD=3601
config.Nims.0.diseqcA=282
config.Nims.0.diseqcB=3601
config.Nims.0.diseqcC=3601
config.Nims.0.diseqcD=3601

If so, try following: putting Enigma to sleep with an init 4 command then delete the lines with 3601. (A single tuner will come up as diseqcA, so leave that as it is)

config.Nims.1.diseqcA=282
config.Nims.0.diseqcA=282

 

[sledge121]

Abu, you are a legend, it actually worked after I changed the settings, I'm hoping it wasn't just the GUI restart that fixed it, will update when I know, would the same two lines work on a solo or would it just be one line?

Thanks
Sledge

 

[abu baniaz]

It would be just one line as it only has one tuner. Just delete the 3601 lines.

IIRC, they only get written when selecting auto. Subsequent manual setting does not seem to remove them. Could have changed, not tried it for a while.

 

[sledge121]

it must have been the gui restart that temporarily fixed it, it didnt run on the next schedule.

 

[Joe_90]

I just tried setting a CrossEPG schedule with my Miraclebox. Set it for 5 mins ahead and stayed on channel. Nothing happened. Set it again for 5 mins ahead and went to standby. Nothing happened. Ran fine when I initiated it manually. Looking at the debug log there seems to be some issue with setting the auto schedule - see below:

action ->  SetupActions ok
warning, skin is missing element key_yellow in <class 'Plugins.SystemPlugins.CrossEPG.crossepg_setup.CrossEPG_Setup'>
warning, skin is missing element key_blue in <class 'Plugins.SystemPlugins.CrossEPG.crossepg_setup.CrossEPG_Setup'>
KEY: 352 OK
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 106 RIGHT
action ->  SetupActions right
KEY: 106 RIGHT
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 2 1
KEY: 2 1
KEY: 6 5
KEY: 6 5
KEY: 2 1
KEY: 2 1
KEY: 11 0
KEY: 11 0
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 399 GREEN
action ->  SetupActions save
unknown action SetupActions/save! typo in keymap?
KEY: 399 GREEN
action ->  ColorActions green
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 352 OK
action ->  SetupActions ok
opentv
opentv
warning, skin is missing element key_blue in <class 'Plugins.SystemPlugins.CrossEPG.crossepg_providers.CrossEPG_Providers'>
[SKIN] No skin to read...
KEY: 352 OK
KEY: 399 GREEN
action ->  SetupActions save
unknown action SetupActions/save! typo in keymap?
KEY: 399 GREEN
action ->  ColorActions green
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 352 OK
action ->  SetupActions ok
[SKIN] No skin to read...
KEY: 352 OK
KEY: 399 GREEN
action ->  SetupActions save
unknown action SetupActions/save! typo in keymap?
KEY: 399 GREEN
action ->  ColorActions green
KEY: 108 DOWN
KEY: 108 DOWN
KEY: 174 EXIT
action ->  SetupActions cancel
[CrossEPG_Auto] Schedule Disabled at Fri 08 Aug 2014 15:06:42 IST
KEY: 174 EXIT
KEY: 174 EXIT

 

[sledge121]

Good spot, Where does that leave us with this issue?

 

[Huevos]

I just tried setting a CrossEPG schedule with my Miraclebox. Set it for 5 mins ahead and stayed on channel. Nothing happened. Set it again for 5 mins ahead and went to standby. Nothing happened.

Auto schedule works fine for me on the Ultimo. Is 5 minutes enough lead time?

 

[abu baniaz]

Post contents of file crossepg.config located at /usr/crossepg/

Mine for comparisson

db_root=/hdd/crossepg
lamedb=lamedb
providers=skyuk_astra2_28.2
force_load_on_boot=0
download_daily_enabled=1
download_daily_hours=14
download_daily_minutes=0
download_daily_reboot=1
download_manual_reboot=0
download_standby_enabled=0
last_full_download_timestamp=0
last_partial_download_timestamp=0
last_defrag_timestamp=1407330055
csv_import_enabled=0
show_plugin=0
show_extension=1
show_force_reload_as_plugin=0
configured=1

 

[sledge121]

Good call, I wondered where the config file was.

root@vusolo2:~# cat /usr/crossepg/crossepg.config
db_root=/hdd/crossepg
lamedb=lamedb
providers=skyuk_astra2_28.2
force_load_on_boot=0
download_daily_enabled=1
download_daily_hours=4
download_daily_minutes=7
download_daily_reboot=1
download_manual_reboot=0
download_standby_enabled=0
last_full_download_timestamp=0
last_partial_download_timestamp=0
last_defrag_timestamp=1407338424
csv_import_enabled=0
show_plugin=1
show_extension=1
show_force_reload_as_plugin=0
configured=1

 

[Joe_90]

Good spot, Where does that leave us with this issue?

Not sure, because it works fine at the moment on my Quad Plus, so I don't want to go changing anything in case it breaks

edit - had a look at the config files on both Quad Plus and Miraclebox. Nothing out of the ordinary and same as both of yours except for the time. I wonder what system watchdog triggers the running of Crossepg - cron? Maybe you have to have power timer enabled? I only have power timer running on the Quad+. I only run CrosseEPG manually on the MB as needed. I've left it in standby to see if it triggers later this afternoon (16:00).

 

[Huevos]

Not sure, because it works fine at the moment on my Quad Plus, so I don't want to go changing anything in case it breaks

edit - had a look at the config files on both Quad Plus and Miraclebox. Nothing out of the ordinary and same as both of yours except for the time. I wonder what system watchdog triggers the running of Crossepg - cron? Maybe you have to have power timer enabled? I only have power timer running on the Quad+. I only run CrosseEPG manually on the MB as needed. I've left it in standby to see if it triggers later this afternoon (16:00).

Like I said, is 5 minutes enough lead time? And does it need a restart after your change? My auto schedule works fine but if I reset it 5 minutes ahead it doesn't do anything.

 

[Joe_90]

Like I said, is 5 minutes enough lead time? And does it need a restart after your change? My auto schedule works fine but if I reset it 5 minutes ahead it doesn't do anything.

My auto schedule (on the Quad+) is also working fine. What's enough lead time - 10mins? 30mins? I suppose the answer is - it depends! Need a coder to throw some light on the issue.

 

[danivtec]

Sure my duo 2 has about 5 minutes between running a bouquet scan and crossepg. No issues seen with build 23.