[GiGaBlue QUAD] Boblight, how to identify the usb output?

[andysev]

Hello everyone.

I am trying to run the plugin Boblight.

I have a adalight, and it works because I got the PC working.

the problem I have is that the set, I have to tell the USB output. Inside the folder / dev /.

I've tried: usbdev, ttyACM0 ...

 

[Rob van der Does]

I always struggle with the same issue (for AtmoLight). But it always seems to be /dev/ttyUSB0
Not sure if the same applies to Adalight.

 

[Trial]

Hi,
perhaps you find something with lsusb

ciao

 

[andysev]

yes, I've tried /dev/ttyUSB0 .but does not work.

if I search in /dev/, I do not find ttyUSB. think that's why it does not.

 

[Rob van der Does]

Hmmm, gives me

root@Ultimo:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001
Bus 001 Device 002: ID 0718:061a
Bus 003 Device 002: ID 0403:6001

while the setting in BoB-Light is /dev/ttyUSB0 and works fine

 

[andysev]

Hmmm, gives me

root@Ultimo:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001
Bus 001 Device 002: ID 0718:061a
Bus 003 Device 002: ID 0403:6001

while the setting in BoB-Light is /dev/ttyUSB0 and works fine

hi, thanks for answering. you have it so? have you tried it?, I am surprised me a lot that does not work when the PC runs a clone of the vu + solo too. In vu+ solo clone, I had to find the correct file in the folder: / dev /, " /dev/ttyACM0"

 

[judge]

I am surprised me a lot that does not work when the PC runs a clone of the vu + solo too. In vu+ solo clone, I had to find the correct file in the folder: / dev /, " /dev/ttyACM0"

And there ends your support here, please re-read the site rules.

 

[andysev]

I'm sorry, I understand the rule of NO clones. But I have NO problem with that deco. I have a Gigablue QUAD, original. simply to a reference. not request support for deco clone.

 

[andysev]

anyone have a working boblight with Openvix? I can not get to the problem.

 

[Rob van der Does]

anyone have a working boblight with Openvix?

Yes .

 

[andysev]

Yes .

and you use the route: /dev/ttyUSB0 ?

gigablue quad ? you can tell me exactly which USB port you have connected?

 

[Rob van der Does]

/dev/ttyUSB0 ([STRIKE]bottom[/STRIKE] upper port at back) for Atmolight on Ultimo & DUO2

 

[andysev]

/dev/ttyUSB0 ([STRIKE]bottom[/STRIKE] upper port at back) for Atmolight on Ultimo & DUO2

ok, thank you very much for the info. But I do not operate that route, I will try to contact boblight developer.

And I will continue looking for someone who has working in Gigablue quad.

 

[andysev]

Ok, problem solved.

With the latest version: 0.8r5

And the route: / dev/ttyACM0

working perfectly, ardulitgh with 120 leds.

 

[Rob van der Does]

Good to hear that: enjoy your lightnings!

How did you find out about '/dev/ttyACM0'?

 

[andysev]

I found a video on youtube, a GG quad with boblight working.

This video is from a German store, send them a mail. and they have answered me.

I had already tried that route. but not with the latest version, which is a few days ago.

"Asking, one gets to Rome"