[ET9x00] New ViX Team ET 9x00 OE3.0 Release Discussion

[beson]

Hi m8:s and thanks for the VIX 3.0 release.
I have a question though. Which version of oscam shall I use for the 3.0 image.
I have tried a couple of versions now, like 6908 and 1.10 stable version.
Which OE version of oscam to use with VIX 3.0?
The problem is, when starting from deep standby, I have to go into softcam manager everytime and manually start oscam.
On 2.4 I was using 6908 with no problems.

beson

Ok, I'll take this one more time.
My problem is that oscam is not autostarting.
I have to start oscam from softcam manager after starting the box from deep standby.
After that oscam is running perfect.

beson

 

[Larry-G]

Ok, I'll take this one more time.
My problem is that oscam is not autostarting.
I have to start oscam from softcam manager after starting the box from deep standby.
After that oscam is running perfect.

beson

provide us with debug logs so that we may try to track the problem down.

 

[beson]

Ok, I found out what was wrong.
It was a silly mistake from me. I had forgotten to tick and activate "enable startup" for oscam in softcam setup
Now I will hopefully never do that mistake again.
Thanks anyway guys.

beson

 

[Larry-G]

Ok, I found out what was wrong.
It was a silly mistake from me. I had forgotten to tick and activate "enable startup" for oscam in softcam setup
Now I will hopefully never do that mistake again.
Thanks anyway guys.

beson

no worries, at least your now sorted.

 

[shaft]

Hi Guys

I am baffled by this! I have flashed the new image, but am now unable to connect to my 9100 to upload any necessary files.
I had been using the ET9000CC console to upload files but it now refuses to connect.

I get an "access violation at address 0052E98E in module 'ET9000CC.exe', Read of address 00000000." error message.

My settings are the same as the old 2.4 image and my network test within the 9100 works fine.

I tried using Filezilla to connect to my box but get an "500 OOPS: cannot locate user entry:vsftpd" critical error. All looks ok in the FTP setup settings on the 9100:

Vsftpd server current status = Running.

I use a static ip but have also tried via dhcp - neither way connects to my 9100!

Can anyone see where I am going wrong or is there any other method of uploading system files from my laptop to my 9100?

Any help gratefully received!! Please!

shaft.

 

[judge]

Hi Guys

I am baffled by this! I have flashed the new image, but am now unable to connect to my 9100 to upload any necessary files.
I had been using the ET9000CC console to upload files but it now refuses to connect.

I get an "access violation at address 0052E98E in module 'ET9000CC.exe', Read of address 00000000." error message.

My settings are the same as the old 2.4 image and my network test within the 9100 works fine.

I tried using Filezilla to connect to my box but get an "500 OOPS: cannot locate user entry:vsftpd" critical error. All looks ok in the FTP setup settings on the 9100:

Vsftpd server current status = Running.

I use a static ip but have also tried via dhcp - neither way connects to my 9100!

Can anyone see where I am going wrong or is there any other method of uploading system files from my laptop to my 9100?

Any help gratefully receved!! Please!

shaft.

You used a 2.4 settings restore, didn't you?

 

[shaft]

...May have done

 

[shaft]

Reflash then?

 

[judge]

Yes.
It is in big letters in the first post, you know...

 

[shaft]

Yeah ok

But who reads instructions?

Thanks judge!

 

[shaft]

Another problem guys.

I cannot get my Netgear wireless dongle (WG111v3) to work with the new build. It worked flawlessly with the last build but will not connect with the new.

I have tried via DHCP and static IP. It sees my wifi router but refuses to connect.

I have tried restarting the network, the box and the router, re-entering the WPA-PSK password.

It works fine via a LAN set up, using DHCP or static...

shaft.

 

[punisher]

what security type are you using? WPA or WPA2 or WEP... try using different one and see what works for u

 

[shaft]

Changed my router to WPA2 and it worked!

Thanks a lot punisher!!

 

[punisher]

no worries mate, glad you sorted

 

[Rimmel]

Hi guys just reflashed and now mkv's lose sound randomly.

Any ideas?

thanks
CT

 

[Rimmel]

Hi guys just reflashed and now mkv's lose sound randomly.

Any ideas?

thanks
CT

Confirmed - same files working perfectly on VIX 2.4

 

[sunday96]

Thank you guys for bringing us these beautiful images with increased functionality.

For some reasons, I have been experiencing some freezes with this latest image. I initially thought it was the key (xxxx.cfg) I was using but I used the same key on one of my other boxes (blackpanther) and it works without any freezes whatsoever.

IS there any setting I need to enable / disable to stop the freezes?

Cheers guys

 

[Rimmel]

Thank you guys for bringing us these beautiful images with increased functionality.

For some reasons, I have been experiencing some freezes with this latest image. I initially thought it was the key (xxxx.cfg) I was using but I used the same key on one of my other boxes (blackpanther) and it works without any freezes whatsoever.

IS there any setting I need to enable / disable to stop the freezes?

Cheers guys

Yes Ive also found the image to not be as sharp and responsive as 2.4.

regards

 

[Rob van der Does]

Yes Ive also found the image to not be as sharp and responsive as 2.4.

Not sure what you mean by an image being (not) sharp & responsive.

 

[punisher]

Not sure what you mean by freezes either... Not experiencing any freezes or lockups or remote response problems