[GiGaBlue QUAD] Gigablue Quad Wont Restart

[casuk]

I have all set up from scratch again same problem, updated to 09 and its still the same, I restart screen go's black with your GBQ+ is rebooting I get a spinner for 1s then disappears and just sits in that screen until I turn it of,

 

[nsw9154]

Just updated to hades 08 and I'm having the reboot problem GUI restart is fine but a full reboot leaves box frozen iv had to restart from switch

I decided to set up my Quad plus again and i had the same issue and vix spinners i even tried Telnet commands to reboot, it stopped the spinner but then locked up again and had to turn it off at the back
i have updated to 009 and it seems better but i have not fully tried it out as i did not get to bed till 7am trying to fix it

 

[casuk]

Iv not disconnected HDD and tryed it that way yet but thats not the problem its a bug in the image, iv enabled debugs but nothing there or crash logs, I'll run the image for the rest of the day and test it out, the image is running fine so far bar the box unable to complete the roboot process

 

[casuk]

Thats the first debug log

 

[outrage_uk]

Gigablue Quad Plus running Hades 009 still doesnt restart with or without HDD - no logs.

 

[casuk]

Hopefully there's a fix soon

 

[Joe_90]

Nothing wrong with Hades 009 on my GB Quad Plus as regards restarting. Goes into deep standby when requested and comes out of deep standby with remote. I also have a Power Timer to wake it up each morning at 06.00 and then it runs ABM and CrossEPG. Maybe your bootloader is out of date? The bootloader was updated last July to cater for bigger partition sizes and new requirements for changes in the underlying OE core. You could try flashing the bootloader http://www.openvix.co.uk/index.php?dir=Bootloaders/GiGaBlue-Bootloaders/GiGaBlue-QUAD%20PLUS/ followed by a clean flash of Hades 009.

 

[casuk]

I flashed bootloader a week or two ago done a clean install of apollo 166 and was ok, ill flash bootloader again later, iv just put open atv in it and all is running fine no problems at all, i think it could be my usb

 

[Joe_90]

If you've already flashed the newer bootloader, there is no point in flashing it again. No point in risking bricking the box. When you say you think it could be your usb, do you mean the stick you're flashing from? In which case I definitely wouldn't be flashing bootloaders from it!

 

[casuk]

If you've already flashed the newer bootloader, there is no point in flashing it again. No point in risking bricking the box. When you say you think it could be your usb, do you mean the stick you're flashing from? In which case I definitely wouldn't be flashing bootloaders from it!

I flashed bootloader then hades 09, restarted and it booted up no problems I put mgcamed in and the files in and no rebbot I took the files and unistalled mgcamed and its not rebooting,

 

[nsw9154]

I am having the same problem with my Quad plus tony if i do a GUI restart it reboots ok but if i do a normal restart it just stops and will not reboot until you switch it off at the back, i have just tried rebooting it with a Telnet command and it rebooted as normal, then tried pressing restart and it is now stuck on a blank screen and the TV saying no signal so i am going to have to switch it of at the back to get it to reboot running the latest Hades 009 update

 

[casuk]

after a lot off messing about all day in fact, I now know it is mgcamed that will not allow the box to reboot, I have used mgcamed 1.35a and 1.38 both doing the same if I disable startup and stop the cam it boots if I start cam and activate cam at start up and restart it will not boot, i also tryed with just cccam and no mgcamed and it done the same thing

 

[gdhkr]

As this been fixed ? Still 04 until a fix is out !


Sent from my iPhone using Tapatalk

 

[casuk]

No still the same on build 10 maybe next update it will be sorted

 

[Sicilian]

No still the same on build 10 maybe next update it will be sorted

Unless anyone can post boot logs not a lot can be done, in all honesty sounds like a possible driver issue.

 

[casuk]

Unless anyone can post boot logs not a lot can be done, in all honesty sounds like a possible driver issue.

How do you post boot logs, its the cam being active thats causing it

 

[gdhkr]

I sent a log a few days back


Sent from my iPhone using Tapatalk

 

[casuk]

Iv been sending debugs, not sure if the same thing

 

[gdhkr]

Just turn off my mganmd still didn't reboot must be a driver issue


Sent from my iPhone using Tapatalk

 

[Sicilian]

We need RS232 logs from a reboot.