[GiGaBlue UHD QUAD 4K] Power Timer AutoDeepStandby Inoperative

[CRMS]

I've just updated from 5.4.016 to 6.2.011. In 5.4 I used the plugin StartupToStandby (SToS) and the power timer AutoDeepStandby (ADS) and both worked perfectly. With 6.2, I had to get a revised SToS plugin for Python 3, and it now runs fine as before.
But ADS won't run at all and after 10 mins the box remains in Standby. I've deleted the power timer, restarted box and reinstalled a few times.

I attach the latest debug file. The power timer entry is at 40.3783 seconds.


View attachment Enigma2_debug_2022-12-23_16-50-13.log


Also is there any way of giving the box a permanent IP address??

 

[Joe_90]

The IP address given to the box is a function of DHCP in whatever you are using as a modem/router. Usually it's under a heading called "Address Reservation" or similar. You assign a fixed IP address to a device MAC.

As regards the AutoDeepStandby, all I can see is that some plugin called "MovieOrganisor" (sic) is running at 17:00, just about when 10 minutes have elapsed and ADS should be checking whether to standby (or deep standby). The MovieOrganisor(sic) is throwing lots of "Invalid argument" messages at around that time. The log stops at that point.

Do you have a screenshot of the PowerTimer settings? Here are mine. ADS only kicks in on my box if I have it already in standby. It means that we just hit the power button on the remote, which puts the box in standby and 20 mins later it goes to deep.


EDIT - The actual PowerTimer entry settings in the menu will display its own log if you press the info key when on the entry. See the second screenshot where it goes to status 3 at 13:28. Before that, the box was in use and I had only put it in standby shortly before the last entries.

 

[twol]

I've just updated from 5.4.016 to 6.2.011. In 5.4 I used the plugin StartupToStandby (SToS) and the power timer AutoDeepStandby (ADS) and both worked perfectly. With 6.2, I had to get a revised SToS plugin for Python 3, and it now runs fine as before.
But ADS won't run at all and after 10 mins the box remains in Standby. I've deleted the power timer, restarted box and reinstalled a few times.

I attach the latest debug file. The power timer entry is at 40.3783 seconds.


View attachment 64570


Also is there any way of giving the box a permanent IP address??

Change logs to use local time … much easier to follow whats happening

 

[twol]

I've just updated from 5.4.016 to 6.2.011. In 5.4 I used the plugin StartupToStandby (SToS) and the power timer AutoDeepStandby (ADS) and both worked perfectly. With 6.2, I had to get a revised SToS plugin for Python 3, and it now runs fine as before.
But ADS won't run at all and after 10 mins the box remains in Standby. I've deleted the power timer, restarted box and reinstalled a few times.

I attach the latest debug file. The power timer entry is at 40.3783 seconds.


View attachment 64570


Also is there any way of giving the box a permanent IP address??

All my boxes are set to static IP ….. just say no to DHCP and enter an ip address below. normally I ahve a router that allocates upto 100 through DHCP and the rest I allocate out to various boxes

 

[Joe_90]

Change logs to use local time … much easier to follow whats happening

The log from @CRMS is using local time.

 

[Joe_90]

All my boxes are set to static IP ….. just say no to DHCP and enter an ip address below. normally I ahve a router that allocates upto 100 through DHCP and the rest I allocate out to various boxes

@CRMS can certainly do that, but then he needs to ensure that the IP address is not in the range of DHCP given out by the router (as you have), otherwise he runs the risk of duplicate addressing. If the number of fixed IP devices is limited, it's just as easy to make the router allocate the addresses. I allocate about 40 IP addresses in the router and name the devices so that I have a central repository or master list of all my boxes.

 

[birdman]

I attach the latest debug file. The power timer entry is at 40.3783 seconds.

Go into the Power Timer list in the Menus and press Info.
This will tell you what is (not) happening.

 

[Joe_90]

... see post #2 @birdman, where I showed the info list on PowerTimer.

 

[birdman]

... see post #2 @birdman, where I showed the info list on PowerTimer.

Sorry - managed to miss that...

The box doesn't appear to be in Standby, but that is a required test for the PowerTimer.
The log has this in it:

<    85.5161> 16:51:17.7123 [Standby] leave standby
...
<    85.6646> 16:51:17.8607 [LED-GIGA] Leave Standby

and these are the last mentions of Standby status.

 

[CRMS]

Thanks.
On the ADS info read out I just get back off every 10 minutes, same as the delay time.

I'll boot from 5.4.016 and compare debug logs.

I have also deleted Movieorganisor plugin in case that was interfering, but no difference.
Arguably Movieorganisor functionality should be built into OpenVix anyway as it puts serial recordings into appropriate folders, keeping a series of programmes together.

I'm back to setting the standby option in the timer settings on the last programme recording at night, which is what I used to do before finding the simple Power Timer option.

Merry Christmas everyone.

 

[Joe_90]

If you're getting the "backoff" message it means the system is busy or a recording is due. My PowerTimer only goes to deep if the box is already in standby.

Serial recordings (like soaps etc.) can be put into pseudo-folders automatically by OpenVix. Look for a setting referring to Collections - I think it's in Recordings menu - not near my box at the moment. It's a very useful facility.

Merry Christmas!

 

[CRMS]

Yes, I'm aware that it won't go into ADS if there is a recording coming up and it has to be in stand by first.
I'll look at Collections.