[GiGaBlue QUAD] Gigablue Quad Wont Restart

[casuk]

Stop mgcam and disable start up then it reboots

 

[outrage_uk]

Yeh just to confirm ive stopped and disabled mgcamd 1.38 start up and rebooting is now working.

Ive an RS232 cable and an old computer with a serial port, how do I get logs?

 

[Sicilian]

Yeh just to confirm ive stopped and disabled mgcamd 1.38 start up and rebooting is now working.

Ive an RS232 cable and an old computer with a serial port, how do I get logs?

Use Putty

http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

Setup Putty for RS232, leave it running.

1) Power on Quad+
2) Ensure MGcamd is set to autostart and reboot.

Please grab a complete log, from power on and through the reboot after enabling MGcamd to autostart.

 

[dermies]

Just upgraded from 153 to Hades 10, also on Gigablue Quad.
Getting same issue with not rebooting properly and having to turn it off.

Turned Debug on so hopefully Log attached.

 

[Sicilian]

Just upgraded from 153 to Hades 10, also on Gigablue Quad.
Getting same issue with not rebooting properly and having to turn it off.

Turned Debug on so hopefully Log attached.

Are you using MGcamd?

There was a driver update on 1st May https://github.com/oe-alliance/oe-alliance-core/commit/247263e963b6f592bfe981cdb23263e15e0683b5

Please can someone try Hades 004, flashed and setup fresh http://www.openvix.co.uk/index.php?dir=GiGaBlue-HD-QUAD-PLUS/

Anyone using MGcamd may need to switch to another softcam like Oscam.

 

[dermies]

Are you using MGcamd?

Yes, 1.38 but I think the restart issue was there before installing it.

 

[casuk]

Cccam causes the same problem ill flash 04 just now and set it up from scratch

 

[casuk]

Boots up no probs using hades 04, mgcam active and start up enabled, ill online update to 10 after setting up and see if it boots

 

[outrage_uk]

I've attached serial logs.

The Load is while it turns on, the Restart is after ive told it to restart if you couldn't work it out

 

[Sicilian]

I've just logs myself too and reported to engineers.

I suggest you guys revert to build 004 for now.

 

[nsw9154]

I have been building my own PC's for 20 years and the one cable that i have never used or even purchased is a RS232 cable

just in the middle of installing 004 on the Quad +

 

[Sicilian]

Build 004 should be fine, it has older drivers.

 

[Sicilian]

Boots up no probs using hades 04, mgcam active and start up enabled, ill online update to 10 after setting up and see if it boots

NO!! You have to stay on build 004 or you will have same issue again!

 

[nsw9154]

It will be the best thing to just use 004 until the Driver issue is sorted as Hades will still work fine, i remember when the LX3 had Driver problems and it was sorted in about 10 builds
but saying that Gigablue took ages to sort out the temperature glitch that was down to bad drivers so do not hold your breath
I was put of buying a Quad + for 12 month because i thought that you could fry eggs on it as it got that hot but that was down to Drivers again and nothing to do with the vix image

 

[casuk]

Ok ill stay put just now then

 

[Sicilian]

Oscam should be fine on 010.

 

[nsw9154]

Never tried Oscam

 

[gdhkr]

Gone back to 166 seems more stable for now


Sent from my iPhone using Tapatalk

 

[casuk]

Im using 166 aswel runs good, i did have aproblem when i recorded a timeshift and it locked up when another timer started and timeshift recording came to an end, iv had a couple of problems with timeshift on this image

 

[Sicilian]

Hades 004 should be fine.