[VU+ Solo2] VU+ Solo2 Update to openvix-5.2.025 ABM not working

[jayzy1]

Hi I just updated my VU+ Solo2 to openvix-5.2.025 after long time being on v4, and after update I just cant seem to get ABM working/scaning Freeesat. Been away for some time so Am I missing something obvious?
Both tuners are working fine, providers list shows up both Freesat & Sky, but when I scan it freezes after @40% or 60% and says Tuner B error, or if I disable tuner B, then Tuner A error.

Any help much appreciated.

 

[cactikid]

Maybe your on an old version of abm as usually deletion of abm and download a fresh version from plugins feed.
One can remove plugins from the feed and install newer versions from the feeds.

 

[spanner123]

Maybe your on an old version of abm as usually deletion of abm and download a fresh version from plugins feed.
One can remove plugins from the feed and install newer versions from the feeds.

Doesn't an openvix update include the latest versions of plugins?

 

[ccs]

Maybe your on an old version of abm as usually deletion of abm and download a fresh version from plugins feed.
One can remove plugins from the feed and install newer versions from the feeds.

Updating from 4.? to 5.2.025 would have needed a reflash, so no way will ABM be out of date.

 

[Andy_Hazza]

Hi I just updated my VU+ Solo2 to openvix-5.2.025 after long time being on v4, and after update I just cant seem to get ABM working/scaning Freeesat. Been away for some time so Am I missing something obvious?
Both tuners are working fine, providers list shows up both Freesat & Sky, but when I scan it freezes after @40% or 60% and says Tuner B error, or if I disable tuner B, then Tuner A error.

Any help much appreciated.
View attachment 58220View attachment 58221

Change both tuners to Advanced, 28.2, LNB1

Then double check your cabling to your receiver and rescan ABM.


Sent from my iPhone using Tapatalk

 

[abu baniaz]

You probably have a hardware/alignment fault with reception equipment. Dish/lnb/cabling.

ABM uses the following frequency for Freesat:-
frequency="11426000"
symbol_rate="27500000"
polarization="Horizontal"

Check signal finder that you can receive that frequency. If you cannot, ABM will fail for you when processing Freesat.

Also, if you perform a complete scan of 28.2, not using ABM, you should get 900+ channels

Please read the following thread too
https://www.world-of-satellite.com/...ase-read-before-raising-ABM-support-questions

 

[jayzy1]

Thanks all

Yes did a complete reflash and no restore to latest Vix
Tried delete ABM and installed again - still same error
I can do a manual scan and finds all channels so Tuner & cabling is fine

 

[abu baniaz]

I can do a manual scan and finds all channels so Tuner & cabling is fine

How would you know you are not missing any? Say the number of channels you are finding during a scan. Do not enable network scan.

Can you please post a screenshot showing your tuner locking onto the frequency I mentioned earlier

 

[abu baniaz]

Still working fine for me

< 44564.350> [ABM-main][doTune] Search NIM for orbital position 282
< 44564.364> [eDVBResourceManager] another linked frontend is in use.. so allocateFrontendByIndex not possible!
< 44564.379> [ABM-main][doTune] Nim found on slot id 0 but it's busy. Stopping active service
< 44564.453> [eDVBFrontend0] prepare_sat System 0 Freq 11426000 Pol 0 SR 27500000 INV 2 FEC 0 orbpos 282 system 0 modulation 1 pilot 2, rolloff 0, is_id -1, pls_mode 0, pls_code 1
< 44564.453> [eDVBFrontend0] tuning to 1212 mhz
< 44564.453> [eDVBChannel] OURSTATE: tuning
< 44564.897> [ABM-main][checkTunerLock] ACQUIRING TSID/ONID
< 44564.999> [ABM-Manager][read] Reading sat_282_freesat (hd_freesat_110_1)...

 

[jayzy1]

maybe I wasnt clear, let me clarify, ABM used to work just fine on the old V4 Vix

When I enable providers Sky & Freesat UK in ABM, it freezes and I get tuner error,
when I disable Freesat and only leave Sky UK East Midlands then the ABM scan completes

So seems it is an issue with Freesat UK. This is my tuner setting:

 

[Huevos]

Read post #6 again. Test both tuners in signal finder. Provide screen grabs. Read the link in Abu's signature how to do a proper screen grab.