[Zgemma H9 Twin] set openvix for 27.5w

[v12nut]

Hi all,
What steps/files are required to set up Openvix 5.3.028 for using 27.5w ?
cheers

 

[twol]

Same as OpenPli .... the thread you posted in is probably “the“ source - so what is your actual question, as if I read your OpenPli post correctly you had it working?

 

[v12nut]

Same as OpenPli .... the thread you posted in is probably “the“ source - so what is your actual question, as if I read your OpenPli post correctly you had it working?

Yes I did and that post was sometime back, anyhow, I updated the openpli 7.2 today and for whatever reason all the channels on 27.5 would not open and then oscam.emu would not work.
Not succeeding in fixing it I thought meantime why not try another image, which brought me to my original question.
Regards

 

[twol]

1) did you scan 27.5W and break the changes to the lamedb??
2) you don‘t need oscam emu - on ViX oscamlatest is fine.
3) what files are you currently using?
Important that the lamedb is obviously set up for 27.5W, but I use a very bog standard oscam.conf, oscam.server set up as a BISS reader

[reader]
label=BISS
protocol=constcw
device=/etc/tuxbox/config/constant.cw
caid=2600
group=1

And a file constant.cw containing the transponders etc

 

[v12nut]

1) did you scan 27.5W and break the changes to the lamedb??
2) you don‘t need oscam emu - on ViX oscamlatest is fine.
3) what files are you currently using?
Important that the lamedb is obviously set up for 27.5W, but I use a very bog standard oscam.conf, oscam.server set up as a BISS reader

[reader]
label=BISS
protocol=constcw
device=/etc/tuxbox/config/constant.cw
caid=2600
group=1

And a file constant.cw containing the transponders etc

Thanks for the quick reply,
1 I did scan 27.5w but did not realise there were any changes to be made
2 this was another thing that threw me, in openpli oscam has the constant cw already in it
3 just the lamedb and keys files

and now that I am trying to check the above with DCC I find that the Multiboot is not allowing me access to the zgemma! what a fun day!
cheers

 

[v12nut]

Morning,
as I told you yesterday since using the Multiboot for Pli and Vix I have lost access to the zgemma h9 twin when using DCC (had no problem previously) I have attached a screen shot from DCC, have you had this problem? or know how I can reset it?
regards

 

[twol]

Morning,
as I told you yesterday since using the Multiboot for Pli and Vix I have lost access to the zgemma h9 twin when using DCC (had no problem previously) I have attached a screen shot from DCC, have you had this problem? or know how I can reset it?
regardsView attachment 60196

I am sure its not a multiboot issue - goes nowhere near network.... there are/have been issues with DCC and getting a version that works with OE-A images see https://www.world-of-satellite.com/showthread.php?10166-DCC-E2-(-Dreambox-Control-Centre)
or: better still use Putty

 

[Andy_Hazza]

Putty or use Filezilla Client FTP


Sent from my iPhone using Tapatalk

 

[v12nut]

Putty or use Filezilla Client FTP


Sent from my iPhone using Tapatalk

Thanks I shall try both of those, If you look at the pic at the bottom box there is mention of a TBS server, I get this when connecting to the Zgemma via a crossover cable, no router.any idea why this should be?
regards

 

[twol]

Thanks I shall try both of those, If you look at the pic at the bottom box there is mention of a TBS server, I get this when connecting to the Zgemma via a crossover cable, no router.any idea why this should be?
regards

Sorry, never used the DCC package - no idea.

 

[Joe_90]

Thanks I shall try both of those, If you look at the pic at the bottom box there is mention of a TBS server, I get this when connecting to the Zgemma via a crossover cable, no router.any idea why this should be?
regards

Is this an ethernet crossover cable? If so, how are you allocating IP addresses to the Zgemma and the (I assume) PC? I'm just wondering if this is a simple failure to connect? Using a router with DHCP is probably the most reliable way of connecting. You can either fix address reservations in the router or assign specific addresses in both devices ensuring they are in the same subnet.

 

[v12nut]

Is this an ethernet crossover cable? If so, how are you allocating IP addresses to the Zgemma and the (I assume) PC? I'm just wondering if this is a simple failure to connect? Using a router with DHCP is probably the most reliable way of connecting. You can either fix address reservations in the router or assign specific addresses in both devices ensuring they are in the same subnet.

Yes it is an ethernet cable, which had worked fine with DCC until I installed another image via the zgemma multi boot system, now the same program and cable wont connect or recognise the box.
cheers

 

[Joe_90]

It's likely that the new image has no IP address, then. You need to connect the zgemma to a router in order to obtain an IP address. Then you can connect to it from the PC, either via the router or subsequently directly using a crossover cable (although most ethernet ports will handle a straight or crossover cable).

 

[v12nut]

Hi,
Update, I have all channels back but no sound, could I ask you for a copy of your working lamdb file or what do I need to insert in my own?
cheers

 

[Andy_Hazza]

Sound is nothing to do with lamdb file. Remote not on Mute? Remote not on 0% volume?

A simple Reboot of the receiver via the Menu may solve it?


Sent from my iPhone using Tapatalk

 

[Joe_90]

Hi,
Update, I have all channels back but no sound, could I ask you for a copy of your working lamdb file or what do I need to insert in my own?
cheers

Say what? Did my suggestion allow your PC to connect to the zgemma?

 

[twol]

Hi,
Update, I have all channels back but no sound, could I ask you for a copy of your working lamdb file or what do I need to insert in my own?
cheers

So what did you do to cause this? You need to communicate what you are doing/have done - otherwise you generate loads of responses from people trying to help you - just shipping a copy of the lamedb may or may not help you.

 

[v12nut]

Sort of, as per your suggestion I double checked that both images had functioning network, once that was done I tried connecting with DCC again and it worked!

 

[v12nut]

Take your point, basically all I have done is take the comments given by yourself and fat tony, checked and double checked, turns out there was no network set up on both the images I have on the box which when I sorted out the ip address I could then communicate with the box and and install keys and lamebd files, so now I have picture on the OpenPli but not on opevix yet, however no sound, and thats it to date

 

[Joe_90]

So, thanks for pointing you in the right direction as regards network connectivity, perhaps? Now, 27.5W decryption is above my pay grade, so @twol may be able to point you in the right direction. If you are getting picture, but no sound it would strike me that you are not using the correct PID values for the sound carrier. Maybe look in that area?