Openvix Crash Log

[abu baniaz]

hybrid = choose between DVB-C and DVB-T/T2. You can only use one mode at a time.

To be able to record from more than one frequency/transponder, you need a twin tuner.

N.B:
The Vu twin hybrid tuner has only one wire connection. It has an inbuilt splitter.

Sent from my XT1032 using Forum Fiend v1.3.3.

 

[grantdavey91]

hybrid = choose between DVB-C and DVB-T/T2. You can only use one mode at a time.

To be able to record from more than one frequency/transponder, you need a twin tuner.

N.B:
The Vu twin hybrid tuner has only one wire connection. It has an inbuilt splitter.

Sent from my XT1032 using Forum Fiend v1.3.3.

Thanks for the info much appreciated.

So one the tuner it has an in connection and an out, the in I am guessing I will plug the cable feed into but what can the out be used for?

If it has a built in Splitter does that mean I can record one whilst watching another with one sat feed in?


Thanks

 

[Andy_Hazza]

Yes to everything you've said. [emoji1360]
Glad you got it sorted in the end. All you need to remember when you install the new Hybrid cable tuner is to configure it in your tuner config setup. No need to insert your Net ID there, Net ID only needs to be entered in your ABM providers list. [emoji4]


Sent from my iPhone using Tapatalk

 

[grantdavey91]

Yes to everything you've said. [emoji1360]
Glad you got it sorted in the end. All you need to remember when you install the new Hybrid cable tuner is to configure it in your tuner config setup. No need to insert your Net ID there, Net ID only needs to be entered in your ABM providers list. [emoji4]


Sent from my iPhone using Tapatalk

Thanks Andy, all I needed to know except what will the bottom connection be used for on the tuner?

Thanks

 

[abu baniaz]

it is for daisy chaining to another device. For example, you could have two tuner modules (DVB-C/DVB-T/Hybrid). The signal wire would go into the input. You would then connect the loop wire so signal goes out of tuner. You then connect the loop wire into the input of other tuner.



if you are not going to do so, don't worry about it.

There is a stuck thread in guide section about splitting/looping for DVB-C and DVB-T.













Sent from my XT1032 using Forum Fiend v1.3.3.

 

[grantdavey91]

it is for daisy chaining to another device. For example, you could have two tuner modules (DVB-C/DVB-T/Hybrid). The signal wire would go into the input. You would then connect the loop wire so signal goes out of tuner. You then connect the loop wire into the input of other tuner.



if you are not going to do so, don't worry about it.

There is a stuck thread in guide section about splitting/looping for DVB-C and DVB-T.













Sent from my XT1032 using Forum Fiend v1.3.3.

Ahh thank you abu really sorry I feel quite stupid now this has actually been explained to me before but this was regarding satellite opposed to cable I should've know they'd be for the same use lol

Thanks

 

[grantdavey91]

Ok so i realise it's been what seems quite a while since my last post on this thread but up until today I hadn't got round to sorting this out

I sent back the turbo tuner just over a week ago, and was supposed to have the internal tuner the next day however there was a few faults with shipping and stock and long story short the delivery for the tuner was attempted yesterday

Unfortunately I was out so I missed it and was sent to the RM delivery office !!

Luckily for me my sorting office in my area is open on a Sunday so I collected it this morning and installed it a few hours ago

I was a bit worried about opening up the duo2 so I only did what I needed to and didn't do much as touch anything else!

I've installed the tuner and put box back together, then decided to flash the latest openvix and start afresh

Drum roll....

I am happy to say, no problems whatsoever!!

Box is as fast as ever with switching between cable and satellites and no longer does it freeze

It also stays in standby without freezing

So all I can learn from this experience i guess is stick with internal! - Good riddance to the turbo tuner, had nothing but headaches with it

I've reflashed and downloaded picons/plugins/skin exactly the same setup as before and it works a treat

 

[Andy_Hazza]

Glad you got sorted in the end. [emoji1360]


Sent from my iPhone using Tapatalk